To switch between elapsed time and clock time This also turns recording of trip distance and average speed on or off. When on, the computer records only riding time, and the icon flashes while it is being recorded when off, you must press the START/STOP button to turn the timer on or off. When Elapsed Time, Average Speed, Trip Distance 1 or 2 is displayed, then press the SET (underside) button to turn the icon to the right of the 'A' or 'B'ĭisplay on or off. You may revise the tire size in either 'A' or 'B' as described above. In other modes, you may press the 'SET' button for two seconds at the same time to switch between 'A' and 'B' values. When 'ODO' is displayed, press the 'MODE' and 'START/STOP' buttons at the same time to view the wheel calibration setting. To switch wheel size setting ('A' or 'B'): The clock does not know about daylight savings time: you will have to reset it manually. Press the 'SET' button again to return to normal clock mode, and the 'MODE' button if you would like to return to elapsed time mode. The clock displays 24-hour time if the computer is set to record kilometers, and 12-hour time if to record miles. The 'START/STOP' button will switch between setting the hour and the minute. The hour display will flash and can be changed using the 'MODE' button, more quickly if you hold the button down. If Tm is displayed, press the MODE button for 2 seconds to display the clock time. The calibration number will flicker.Ĭycle through the modes until Tm or the clock is displayed. Use 'START/STOP' (front) button to put into 'stop' state (mile/h symbol not flashing.) Use 'MODE' (top) button to get to 'ODO' mode. Settings may be changed in these modes as described below. Pressing the 'MODE' button will cycle the computer through the modes: When calibration value 'A' is set to desired number, press 'SET' (underside) button to accept and put the computer into normal operation. Use 'MODE' (top) button to raise calibration number, or 'START/STOP' (front) button to decrease it. When total miles/km value is set to desired number, press 'SET' (underside) button to accept and enter wheel calibration mode. Press 'MODE' (top) button to adjust that digit.

Use 'START/STOP' (front) button to change which digit is flashing. Press 'MODE' (top) button for two seconds to enter 'odometer setting' (total km/miles) mode. Press 'MODE' (top) button to select 'mph' (miles) or 'km/h' (kilometers). Push all three buttons at once ('SET' button is on underside of unit.) Do this to clear the computer's memory after replacing the battery: If these buttons are further held down for more than 3 seconds, the wheel calibration value moves between 'A' and 'B' values.įor total reset. When the 'START/STOP' (left) and 'MODE' (right) button are pressed together in 'ODO' mode, first the wheel calibration number appears. To select which weel calibration value to use: Press and hold the 'SET' button for 2 seconds to switch back and forth between 'A' and 'B' calibration value. Press the 'SET' button with a ballpont pen or similar tool. Use 'START/STOP' button to put into 'stop' state (mile/h symbol not flashing.) To revise wheel size without losing mileage: If you hold the 'SET' button for 2 seconds or more, you enter the mode to set the alternate ('B') calibration number. When calibration value 'A' is set to desired number, press 'SET' (recessed) button to accept. Note: This unit permits the entry of two different calibration numbers ('A' & 'B') to allow the same computer to be used with different bicycles Use 'MODE' (right) button to raise calibration number, or 'START/STOP' (left) button to decrease it. When odometer value is set to desired number, press 'SET' (recessed) button to accept and enter wheel calibration mode. Press 'MODE' (right) button to adjust next digit. Use 'START/STOP' (left) button to change flashing digit. Press 'MODE' (right) button to enter 'odometer setting' mode. Use 'START/STOP' (left) button to select 'M' (miles) or 'Km' (kilometers). Press 'MODE' (right) button to enter distance scale selection mode. Push all three buttons at once ('SET' button is recessed on bottom of unit.) If you make a note of the odometer reading before changing batteries, you can re-enter the total distance reading after installing the new battery.

Cateye bike computer manual c137533